Author Topic: Finishing with Acetone vapour  (Read 11442 times)

Offline dale3dps

  • Administrator
  • Jr. Member
  • *****
  • Posts: 68
  • Karma: +0/-0
    • 3D Printing Systems
Finishing with Acetone vapour
« on: March 16, 2013, 03:55:19 PM »
----
Warning:- Using solvents like acetone can be very dangerous. Always carefully read the safety instructions. Don't do this if you don't know what you're doing! Acetone vapour is flamable, do this outside and away from any sparks, electrical equipment.----

The goal is to use acetone vapor to eat away at your model, leaving it with a glossy, injection moulded look and feel.

To do this you will need:
  • Acetone
  • ABS model(s)
  • Plastic/glass container that is not affected by solvents - most lunch box type boxes are suitable - test first!
To process the part you will need to do the following:
  • Pour a small amount of acetone into the container (0.5 - 1cm)
  • Place model in container - have it sitting on something just above the water level.
  • Leave for about 1 hour
  • Check it, and leave for longer until the desired effect is reached.
  • Remove the model and let it air dry
  • Done!
« Last Edit: March 16, 2013, 04:06:50 PM by bruce3dps »


| Sales and Support | www.3dprintingsystems.com | Skype: dale3dps

Offline Stuartblarg

  • Newbie
  • *
  • Posts: 15
  • Karma: +2/-0
  • I just can't stop
Re: Finishing with Acetone vapour
« Reply #1 on: April 08, 2013, 04:34:37 PM »
I have been using a rice cooker with a modified steam tray. The rice cooker heats up and evaporates the acetone which coats the model, melting the outer layers.



I cut out the middle of the steam tray and lowered it into the cooker so that larger parts can be put in the machine.

This whole process take about 3-5 minutes, although if you leave it for too long the model will start to bubble and give an undesired effect.
You will also notice that the colour changes to be a bit lighter than the initial print, this usually happens when the part is drying after the process.   

(Regular print on the left, Acetone treatment good in the middle, on the right was left in the vapor for too long)


These are some other prints with the process applied.



This one i put in for a shorter length of time so it could retain some of the texture from the print.

I really do like this photo




It goes without saying that you should not attempt this without the proper safety equipment, i wear a ventilation mask, safety glasses and gloves while i perform this process and always do so outside. Be very careful not to spill any acetone around the rice cooker or power outlet. 
« Last Edit: April 08, 2013, 11:17:29 PM by Stuartblarg »

Offline Stuartblarg

  • Newbie
  • *
  • Posts: 15
  • Karma: +2/-0
  • I just can't stop
Re: Finishing with Acetone vapour
« Reply #2 on: April 09, 2013, 12:05:34 AM »
These are some examples of colours i have tested so far. All the swatches are in the order of  regular print, good vapor, bad vapor. (sorry for some of the dodgy photos, i need to buy some different coloured backdrops at some point). These are all colours available from the 3D Printing Systems Store.


Silver



Radical Red



Orange Delight



Royal Blue



Sea Green



Crystal Clear



Black Jack

Offline bruce3dps

  • Administrator
  • Jr. Member
  • *****
  • Posts: 58
  • Karma: +5/-0
  • Join the revolution!
    • 3D Printing Systems
Re: Finishing with Acetone vapour
« Reply #3 on: April 09, 2013, 12:13:34 PM »
Wow, thanks for the great post - I am off to get myself a rice steamer!!!

Offline Ziggy

  • Newbie
  • *
  • Posts: 7
  • Karma: +1/-0
Re: Finishing with Acetone vapour
« Reply #4 on: May 06, 2013, 10:24:41 PM »
I've seen people on the interweb using a deep fryer (chip cooker).
One teaspoon of acetone in the bowl.
Model into the mesh basket and into the bowl.
Glass lid goes on.
Low power for 30 seconds.
Bingo.

Get a cheapo deep fryer from Aldi and remember to do it outside and down-wind.

Offline vnkiwi

  • Newbie
  • *
  • Posts: 1
  • Karma: +0/-0
Re: Finishing with Acetone vapour
« Reply #5 on: June 11, 2014, 04:20:45 PM »
i simply 'paint' the acetone on, quickly, with a medium artist brush, used specifically for this.
very quick, and can flood or dribble on. Just the original container and a clean brush, simple.
Works for me
cheers
vnkiwi